HomeMy WebLinkAbout20260653 1 Kaydeross Ave Reverie 73 Signage NOD
Page 1 of 1
Tamie Ehinger, Chair
Rob DuBoff, Vice Chair
Karen Cavotta
Karen D’Andrea
Leslie DiCarlo
Jeff Pfeil
Geoff Wood
Alison Dockum, Alternate
Christina Abele, Alternate
CITY OF SARATOGA SPRINGS
D ESIGN R EVIEW B OARD
❖
City Hall - 474 Broadway
Saratoga Springs, New York 12866
Tel: 518-587-3550 x.2517
www.saratoga-springs.org
NOTICE OF DECISION
In the matter of the application
#20260653
1 Kaydeross Ave Reverie 73 Signage
1 Kaydeross Ave.
Saratoga Springs, New York 12866
involving Architectural review of illuminated monument signage within the Gateway Rural Commercial (GC-R) District, tax parcel
#191.-2-26, within the City of Saratoga Springs.
In accordance with 6 NYCRR Part 617, the Design Review Board classifies this request as a SEQR:
Type II action – exempt from further SEQR review
And, in accordance with the objectives, standards and guidelines contained in the Unified Development Ordinance Article 240 -
13.9 Architectural Review Applicability and Approval Standards, the Design Review Board issues the following decision on
September 9, 2026:
Approve the plans with the following conditions:
The green sections of the top part of the sign are to be opaque and the bottom of the sign is to be non-
illuminated. Address changes to be submitted for administrative approval.
Record of vote:
motion to approve made by L DiCarlo, seconded by J Pfeil passed 5-1
In favor: T Ehinger, K D’Andrea, L DiCarlo, J Pfeil, G Wood
Opposed: R DuBoff
Note: this approval shall expire 18 months from the issuance date unless any necessary building permit has been issued and
actual work begun.
As a result of this decision, the applicant:
may proceed with the proposed project as approved
Please contact the Building Department to verify permit requirements.
Chair Received by Accounts
cc: Building Department
Accounts Dept.
Applicant/Agent
DOUBLE SIDED MONUMENT: SCALE: 3/8”=1’-0”
24.7 SQ.FT. (SAME AS EXISTING)
D/F ILLUM WHITE CABINET WITH 1.50” RETAINERS
FACE: WHITE LEXAN WITH DIGITAL TRANSL PRINT
LED IN CABINET: 3000Kelvin LEDs
POLE COVERS: WHITE (OVER 10” I-BEAMS)
3” x 3” ALUM TUBE FRAME; WHITE .090” ALUM. SKINS
NOTE: SEE FABRICATION AND ATTACHMENT DETAILS ON PAGE 2
CUT VINYL ADDRESS NUMBER
FACE-LIT CHANNEL CELLS (QTY: 2)
FACES: WHT LEXAN
TRIMLESS
RETURNS: 3” DEEP WHITE
WHITE LED LIGHTING:3000Kelvin LEDs
MTD FLUSH
B
2
11.frame details 8/19/26
2-r11
15"
15 1/2"
12"
40"
2 3/16"3"
2” x 2” tube frame cap, .090” alum. faces;
attaches down to lower tube frame
using tamper-resistant at head screws;
removable for access to lower face screws
Dibond or similar LED carriers,
both sides
1-1/4” x 1-1/4” x 1/8” cabinet
frame, skinned with 1/8” alum.,
sides, and bottom, top panel
removable for access inside
040” aluminum sheeting
to cover steel beam, white
Existing 10” steel beam, approx. 100” tall
Power supplies housed in top of sign, accessible
via removable top panel, cut o switch where required
22 3/16"
1-1/2” x 1-1/2” x 1/8” alum. angle
retainer frame
1/8” alum. face with top
and bottom folded anges
for attachment to frame;
screws accessible when
top cap is removed
Existing brick wall, to remain
3” deep trimless channel
letter “cell” design; 3000K LEDS;
attached to frame from inside
alum. frame face
48"
22"
43 7/8"
89"
65 5/8"
24 5/8"10 1/8"6 1/2"
21 3/4"
43 1/2"
65 1/4"
89"
Cabinet installs from inside
through to steel beams
using 3/8”-16 hardware
3/16” thick lexan face
with translucent vinyl applied
Central support tubes/attachment
points for LED dibond carriers
22 1/2"
1/4”-20 hardware into brick anchors
3” x 3” x 1/8” alum. vertical tube supports
2” x 2” x 1/4” alum. angle welded
to frame for attachment to brick
3” x 3” x 1/8” alum. mitered tube frame
Power supply mounted inside sign
63 1/2"
12"
11.frame details 8/19/26
2-r11
FRONT FRAME VIEW
3/4” =1’-0” A SIDE SECTION
3/4” =1’-0” B