HomeMy WebLinkAbout20240299 Cherry St. Single Family Construction Vent Components1Hearth & Home Technologies • Approved Vent Components • 2583-983 Rev. B • 12/22
Vent Components
CAUTION! Risk of Fire! DO NOT store instruction manuals inside fireplace cavity. High temperatures could cause a fire.
INSTALLER: Leave this manual with the appliance, not inside the appliance.
CONSUMER: Retain this manual for future reference. Do not store inside the appliance.
Hearth & Home Technologies Approved Vent Components
This is the list of vent components and termination caps that are approved for use with HHT gas appliances. All caps are
not approved for all appliance models. Consult the Appliance Installation Manual for a complete list of vent components
approved for the specific model being installed. Follow instructions included with vent components for proper installation.
Venting system components have been tested for use with approved HHT Direct Vent appliances. Check with your
local building code agency before you begin installation to ensure compliance with local codes, including the need for per-
mits and follow-up inspections. If you encounter any problems regarding code approvals, or if you need clarification of any
of the instructions contained here, contact your Hearth & Home Technologies dealer. For the dealer nearest you, please
visit www.hearthnhome.com.
Table of Contents
A. DVP Vent Components Diagrams ...................2
B. SLP Vent Components Diagrams ....................7
C. Power Vent Components Diagrams .................11
D. Coaxial / Colinear Components Diagrams ............14
E. Decorative Terminations / Shrouds .................14
WARNING! Risk of Fire! DO NOT install unapproved vent components! Consult appliance Installation
Manual for a list of approved vent components for the specific model being installed.
Hearth & Home Technologies • Approved Vent Components • 2583-983 Rev. B • 12/222
Figure 1 DVP Vent Components
Pipe Effective Length
Inches Millimeters
DVP4 4 102
DVP6 6 152
DVP12 12 305
DVP24 24 610
DVP36 36 914
DVP48 48 1219
DVP6A 3 to 6 76 to 152
DVP12A 3 to 12 76 to 305
10-1/2 in.
(267 mm)
10-7/8 in.
(276 mm)
45 °
7-3/8 in.
(187 mm)
11-3/8 in.
(289 mm)
1-1/4 in. (32 mm)
9-1/4 in.
(235 mm)
13-1/4 in.
(337 mm)
1/2 in. TYP
DVP90ST (90° Elbow)
10 in.
(254 mm)
10 in.
(254 mm)
1 in.
(25 mm)
DVP-FS (Ceiling Firestop)
DVP45 (45º Elbow)
DVP Pipe (see chart)
Effective
Height/Length
4-7/8 in.
(124 mm)
(13 mm)
10 in.
(254 mm)
1- 1/2 in.
(38 mm)
5 in.
(127 mm)12 in.
(305 mm)
UP
DVP-HVS (Vent Support)
12 in.
(305 mm)
14 in.
(356 mm)
1 in.
(25 mm)
8 in.
(203 mm)
6 in.
(152 mm)
DVP-WS (Wall Shield Firestop)
Finished Height: 19-3/4 in./502 mm
UNIV-AS2 (Attic Insulation Shield)
Tab=1 in.
(25.4 mm)
20-3/4 in.
(527 mm)
14 IN.
(356 MM)
14 IN.
(356 MM)
20 IN.
(508 MM)
12 IN.
(305 MM)DVP-RDS
ROOF DECK INSULATION SHIELD
A. DVP Vent Components Diagrams
3Hearth & Home Technologies • Approved Vent Components • 2583-983 Rev. B • 12/22
A. DVP Vent Components Diagrams (continued)
Figure 2 DVP Vent Components
DVP-HPC1
Can adjust 2-1/8 in. (4-1/4 to 6-3/8)
DVP-TRAP1 DVP-TRAP2
DVP-TRAPK2DVP-TRAPK1
DVP-TRAP
Horizontal Termination Cap
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be
used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the
existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a DVP-HSM-B
will be required.
* Center of the horizontal vent pipe to
the vertical measuring surface.
DVP-HPC2
Can adjust 4-1/8 in. (6-3/8 to 10-1/2)
Term Cap Minimum
Effective Length
Maximum
Effective Length
Trap1 3-1/8 in. 4-5/8 in.
79 mm 117 mm
Trap2 5-3/8 in. 9-3/8 in.
137 mm 238 mm
15-1/8 in.
(384 mm)
12 in.
(305 mm)
Heat
Shield
Max
Effective
Length
*5 in.
(127 mm)
8 in.
(203 mm)
Hearth & Home Technologies • Approved Vent Components • 2583-983 Rev. B • 12/224
Figure 3 DVP Vent Components
A. DVP Vent Components Diagrams (continued)
13-1/4 in.
(337 mm)
24-5/8 in.
(625 mm)
27-1/2 in.
(699 mm)
RF6Roof Flashing
31 in.(787 mm)
24-5/8 in.(625 mm)
13-1/4 in.(337 mm)
RF12
Roof Flashing
Cap ShieldDRC-RADIUS
13-7/8 in.
(352 mm)
9-1/2 in.
(241 mm)
14 in.
(356 mm)
COOL-ADDMCap Shield
11-5/8 in.
(295 mm)
5-3/4 in.
(146 mm)
7-1/8 in.
(181 mm)
12-1/8 in.
(308 mm)
DVP-BEK2DVP-HPC Cap Brick Extension
13-7/8 in.
(352 mm)
5 in.
(127 mm)
11-7/8 in.
(302 mm)
DVP-TRAPFL Flashing
26 in.
660 mm
DVP-HSM-B
Extended Heat Shield
TRAP-VSSVinyl Siding Shield
12 IN.
(305 mm)
2-3/8 IN.
(60 mm)
7 IN.
(178 mm)
15/16 IN.(24 mm)
5Hearth & Home Technologies • Approved Vent Components • 2583-983 Rev. B • 12/22
Figure 4 DVP Vent Components
DVP-TB1
Basement Vent Cap
12 in.
(305 mm)
1-1/2 in.
(38 mm)
7-3/8 in.
(187 mm)
14 in.
(356 mm)17-3/4 in.
(451 mm)10-1/2 in.
(267 mm)
3-7/8 in.
(98 mm)
DVP-TV
VerticalTermination Cap
7-1/4 in.
12 in.
305 mm
(184 mm)
5-1/4 in.(133 mm)
12-1/2 in.(318 mm)
DVP-TVHW
VerticalTermination Cap (Highwind)
14 in.
(356 mm)
12 in.
(305 mm)
12-1/8 in.
(314 mm)
7-1/8 in.
(181 mm)
8-3/4 in.
(222 mm)
1-5/8 in.
(41 mm)
16-7/8 in.
(429 mm)
DVP-HPC
High Performance Cap
6 in.
152 mm
A. DVP Vent Components Diagrams (continued)
Hearth & Home Technologies • Approved Vent Components • 2583-983 Rev. B • 12/226
13 in.
(330 mm)
15 in.
(381 mm)
8-1/8 in.
(206 mm)
DVP-HRC-SS
10-7/8 in.
276 mm
10-1/2 in.
267 mm
3°87°
Effective Length
5-3/4 to 8-3/8 in.
146 to 213 mm
5-1/2 in.
140 mm
8-3/8 in.
213 mm
DVP-HRC-ZC-SS
Figure 5 DVP Vent Components
A. DVP Vent Components Diagrams (continued)
7Hearth & Home Technologies • Approved Vent Components • 2583-983 Rev. B • 12/22
B. SLP Vent Components Diagrams
Figure 6 SLP Series Vent Components
8-3/4 in.
222 mm
6-1/2 in.
165 mm
6-5/8 in.
168 mm
6 in.
152 mm
6-1/2 in.
165 mm
6-5/8 in.
168 mm
9-7/8 in.
251 mm
6-1/2 in.
165 mm9-1/4 in.
235 mm
SLP45
45° Elbow
SLP90
90° Elbow
Effective
Height/
Length
SLP PIPE
SLP-HVS
Horizontal Pipe
Support
SLP-FS
Ceiling Firestop
SLP-WS
Wall Shield Firestop
DVP-SLP24
Adapter
6-1/2 in.
165 mm
25-3/16 in.
640 mm
8-1/16 in.
205 mm
10-7/8 in.
276 mm
8-7/8 in.
225 mm
1-1/2 in.
38 mm
8-11/16 in.
220 mm
8-11/16 in.
220 mm
1-1/2 in.
38 mm
12 in.
305 mm
12 in.
305 mm
5-1/2 in.
146 mm
Effective Height/Length
Pipe inches mm
SLP4 4 102
SLP6 6 152
SLP12 12 305
SLP24 24 610
SLP36 36 914
SLP48 48 1219
SLP6A 2 - 6 51 - 152
SLP12A 2 - 12 51 - 305
SLP-FLEX-3 36 914
SLP-FLEX-5 60 1524
SLP-FLEX-10 120 3048
Hearth & Home Technologies • Approved Vent Components • 2583-983 Rev. B • 12/228
B. SLP Vent Components Diagrams (continued)
Figure 7 SLP Series Vent Components
SLP-WT-BK
Wall Thimble-Black
SL-2DVP
Adapter
26 in.
660 mm
DVP-HSM-B
Extended Heat Shield
SLP-TRAP
Horizontal Termination Cap
15-1/8 in.
(384 mm)
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be
used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm)
the existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a
DVP-HSM-B will be required.
Term Cap Minimum
Effective Length
Maximum
Effective Length
Trap1 3-1/8 in. 4-3/4 in.
79 mm 121 mm
Trap2 5-1/4 in. 9-1/4 in.
133 mm 235 mm
12 in.
(305 mm)
14-7/16 in.
367 mm
14-7/16 in.
367 mm
2-5/16 in.
59 mm
3-15/16 in.
(101 mm)
6-11/16 in.
(169 mm)
8 in.
(203 mm)
3-15/16 in.
(101 mm)
3-13/16 in.
(97 mm)
5-1/16 in.
(128 mm)
6-3/8 in.
163 mm
4-3/16 in.
106 mm
4-5/8 in.
117 mm
5-1/16 in.
128 mm8-1/8 in.
206 mm
DVP-2SL
Adapter
4 in.
102 mm
13 in.
(330 mm)
15 in.
(381 mm)
8-1/8 in.
(206 mm)
SLP-HRC-SS
Horizontal Termination Cap
12-5/8 IN.
(321 mm)
12-5/8 IN.
(321 mm)
20 IN.
(508 mm)
10-5/8 IN.
(270 mm)
SLP-RDS
ROOF DECK INSULATION SHIELD
* Center of the horizontal vent pipe to
the vertical measuring surface.
Heat
Shield
Max
Effective
Length
*5 in.
(127 mm)
8 in.
(203 mm)
9Hearth & Home Technologies • Approved Vent Components • 2583-983 Rev. B • 12/22
13 in.
330 mm
13 in.
330 mm
1-5/16 in.
34 mm10-9/16 in.
269 mm
14 in.
356 mm
12-1/2 in.
318 mm
12 in.
305 mm
SLP-CCS-BK
Cathedral Ceiling
Support Box-Black
SLP-DCF-BK
Ceiling Firestop
Black
SLK-SNKD
Snorkel
Termination Cap
SLP-TVHW
Vertical
Termination Cap
13-1/2 in.
343 mm
28-1/2 in.
724 mm
10-11/16 in.
271mm
17-7/8 IN.
454 mm
7-3/8 IN.
187 mm
14 IN.
356 mm
12 IN.
305 mm
SLP-TB1
Basement Vent Cap
4-3/4 in.
121 mm
4-1/8 in.
105 mm
6 IN.152 mm
SLP-FLEX-TRAP
Horizontal
Termination Kit
14-1/16 IN.
357 mm
15-1/16 IN.
383 mm
10-1/16 IN.
256 mm
9 IN.
229 mm
9-7/16 IN.
240 mm
14-1/16 IN.
357 mm
Figure 8 SLP Series Vent Components
B. SLP Vent Components Diagrams (continued)
Hearth & Home Technologies • Approved Vent Components • 2583-983 Rev. B • 12/2210
Figure 9 SLP series Vent Components
B. SLP Vent Components Diagrams (continued)
SLP-HHW2
Horizontal High Wind Termination Cap
15-1/8 in.
(384 mm)
12 in.
(305 mm)
8 in.
(203 mm)
11Hearth & Home Technologies • Approved Vent Components • 2583-983 Rev. B • 12/22
Required Wire Harness
DESCRIPTION PART NUMBER
10 FT PV Wire Harness PVI-WH10
20 FT PV Wire Harness PVI-WH20
40 FT PV Wire Harness PVI-WH40
60 FT PV Wire Harness PVI-WH60
80 FT PV Wire Harness PVI-WH80
100 FT PV Wire Harness PVI-WH100
Note: Wire harnesses required to power the PVLP-SLP connect to the appliance and are ordered separately from
PVLP-SLP. Contact your dealer to order.
Depending on the control system of the appliance, requirements vary. See below. Components are ordered
separately from the power vent. Contact your dealer to order.
For Appliances with an IntelliFire or IntelliFire Plus Control System:
A PV-IPI-CK be installed on this appliance.
Figure 10 PVLP-SLP Vent Components
PVLP-HS
Heat Shield
14 IN.
356 mm
15-1/2 IN.
394 mm
11-1/2 IN.
292 mm
8 IN.
203 mm
4-3/8 IN.
112 mm 10 IN.
254 mm
5-1/4 IN.
135 mm
2-1/4 IN.
57 mm
9-1/2 IN.
241 mm
4-3/4 IN.
121 mm
2-1/4 IN.
57 mm
1-1/2 IN.
38 mm
6-1/4 IN.
159 mm
Front View
Top View
Side View
Note: A PVLP-HS heat shield is available and sold separately. Use if the PVLP-SLP is installed in a high traffic area.
PVLP-BEK
Brick Kit
PVLP-SLP
Power Vent Low Profile
For Appliances with an IntelliFire Touch Control System:
The PVLP-SLP requires one of the following options to be installed on this appliance.
Option A: IFT-RC400 and/or IFT-WFM, IFT-ACM and IntelliFire App that can be downloaded from the app store.
OR
Option B: IFT-RC150, IFT-ACM, IFT-WFM and an IntelliFire App that can be downloaded from the app store. These
accessories are purchased separately from the PVLP-SLP. Contact your dealer to order.
C. Power Vent Components Diagrams
Hearth & Home Technologies • Approved Vent Components • 2583-983 Rev. B • 12/2212
Figure 11 PVV-SLP Vent Components
13-5/8 IN.
13-11/16 IN.
1-3/4 IN.
4 IN.
5-7/8 IN.3-11/16 IN.
12-1/8 IN.
TOP VIEW
SIDE VIEW
Required Wire Harness and PVV-SLEEVE
Lengths Available Part Number
10 ft. PV Wire Harness PVI-WH10
20 ft. PV Wire Harness PVI-WH20
40 ft. PV Wire Harness PVI-WH40
60 ft. PV Wire Harness PVI-WH60
80 ft. PV Wire Harness PVI-WH80
100 ft. PV Wire Harness PVI-WH100
Description Part Number
12 in. Wire Harness Sleeve PVV-SLEEVE-12
48 in. Wire Harness Sleeve PVV-SLEEVE-48
PVV-SLP
Vertical Power Vent
Note: A wire harness is required to power the PVV-SLP and connect it to the appliance. It is ordered separately from
the PVV-SLP. Contact your dealer to order.
Depending on the control system of the appliance, requirements vary. See below. Components are ordered
separately from the power vent. Contact your dealer to order.
For Appliances with an IntelliFire or IntelliFire Plus Control System:
Note: The PVV-SLP requires a PV-IPI-CK be installed on this appliance. The PV-IPI-CK is ordered separately from
the PVV-SLP. Contact your dealer to order.
Note: The PVV-SLEEVE-12 and/or PVV-SLEEVE-48 is required to be installed with the PVV-SLP. It is ordered
separately from the PVV-SLP. Contact your dealer to order.
For Appliances with an IntelliFire Touch Control System:
Note: The PVV-SLP requires one of the following options to be installed on this appliance.
Option A: IFT-RC400 and/or IFT-WFM, IFT-ACM and IntelliFire App that can be downloaded from the app store.
OR
Option B: IFT-RC150, IFT-ACM, IFT-WFM and an IntelliFire App that can be downloaded from the app store. These
accessories are purchased separately from the PVV-SLP. Contact your dealer to order.
C. Power Vent Components Diagrams (continued)
13Hearth & Home Technologies • Approved Vent Components • 2583-983 Rev. B • 12/22
Figure 12 PVI-SLP-B Vent Components
Optional Wire Harness
DESCRIPTION PART NUMBER
10 FT PV Wire Harness PVI-WH10
20 FT PV Wire Harness PVI-WH20
40 FT PV Wire Harness PVI-WH40
60 FT PV Wire Harness PVI-WH60
80 FT PV Wire Harness PVI-WH80
100 FT PV Wire Harness PVI-WH100
PVI-SLP-B
Power Vent Inline
SLP-LPC
SLP Low Profile Cap
(Approved for use with PVI-SLP-B only)
Note: Wire harnesses required to power the PVI-SLP-B connect to the appliance and are ordered separately from
PVI-SLP-B. Contact your dealer to order.
16 IN.
406 mm
15 IN.
(381 mm)
16-11/16 IN.
(424 mm)
9-3/16 IN.
(233 mm)
4-1/2 IN.
114 mm
16-11/16 IN.
424 mm
13-5/8 IN.
(346 mm)
12-1/2 IN.
(318 mm)
12-1/2 IN.
318 mm
20-3/4 IN.
527 mm
13-5/8 IN.
346 mmEFFECTIVE LENGTH
32 IN. (813 mm) MIN.
35 IN. (889 mm) MAX.
Depending on the control system of the appliance, requirements vary. See below. Components are ordered
separately from the power vent. Contact your dealer to order.
For Appliances with an IntelliFire or IntelliFire Plus Control System:
Note: The PVI-SLP-B requires a PV-IPI-CK be installed on this appliance. The PV-IPI-CK is ordered separately from
the PVI-SLP-B. Contact your dealer to order.
For Appliances with an IntelliFire Touch Control System:
Note: The PVI-SLP-B requires one of the following options to be installed on this appliance.
Option A: IFT-RC400 and/or IFT-WFM, IFT-ACM and IntelliFire App that can be downloaded from the app store.
OR
Option B: IFT-RC150, IFT-ACM, IFT-WFM and an IntelliFire App that can be downloaded from the app store. These
accessories are purchased separately from the PVI-SLP-B. Contact your dealer to order.
C. Power Vent Components Diagrams (continued)
Hearth & Home Technologies • Approved Vent Components • 2583-983 Rev. B • 12/2214
LINK-DV30B
Flex Liner Kit
768-380A
Stainless Steel Flex Pipe
DVP-2SL
Adapter
COAXIAL to COLINEAR VENTING
Figure 13 Coaxial / Colinear Vent Components
D. Coaxial / Colinear Components Diagrams
E. Decorative Terminations / Shrouds
Only use listed decorative termination caps/shrouds with Hearth & Home Technologies approved venting systems.
This applies to both DVP and SLP venting systems.
Decorative Terminations Caps/Shrouds
DTO134 Octagon Decor Cap
DTO146 Octagon Decor Cap
DTS134 Square Decor Cap
DTS146 Square Decor Cap
LDS33 Decor Shroud 36 x 36
LDS46 Decor Shroud 48 x 72
LDS-BV Decor Shroud 26 x 26
DV-46DVA-GCL
Coaxial/Colinear Appliance Connector